Kegging
-
$4.005/8 Inch Hex Nut for Keg Coupler or Tap Shank
Chrome plated brass Hex Nut, often used for attaching a tail piece to a shank.
You may also need a tail piece and neoprene washer, available separately.
From: Krome Dispense -
$7.001/4" Shank Tail Piece - Elbow
Stainless steel elbow Tail Piece for your beer shank.
From: Krome Dispense
Material: 304 grade stainless steel
You may also need a hex nut or wing nut, and neoprene washer. -
$5.003/16" Shank Tail Piece - Straight
Stainless steel Tail Piece for your beer shank.
From: Krome Dispense
Material: 304 grade stainless steel
You may also need a hex nut or wing nut, and neoprene washer - available separately. -
$3.40Nukatap (standard) return spring - 62mm
Nukatap Auto-close spring for use with the normal Nukatap. Also compatible with Intertap model, but not compatible with the flow control version of either. -
$36.50K-Lok Female x 3/4 Male (Tap Shank)
The K-Lok adaptors/quick disconnects are compatible with Andale (Snaplok), Lancer Pacific (Fatlock) and other brands of draft beer quick lock fittings that are often seen in commercial pubs and bars.
These are the font adaptors that are designed to fit any fonts with ¾ threaded font such as our Flooded Fonts.
These K-Lok couplers are designed to be a dry break so when you disconnect the male side the flow is cut off.
-
$15.00K-Lok Male x Tap Shank Adaptor
The K-Lok adaptors/quick disconnects are compatible with Andale (Snaplok), Lancer Pacific (Fatlock), Bracton (B-Lock) and other brands of draft beer quick lock fittings that are often seen in commercial pubs and bars.
These fittings include the collet and they attach directly to the back of your tap so the tap fits directly into the K-Lok Female x 3/4 Male (Font Adaptor).
-
$74.00Ultratap S/S - includes handle
Stainless Steel forward sealing Ultrataps to fit the latest Mangrove Jack's Kegerators, are now available individually. Note they can also be used on other homemade/custom kegerators or the like – as they are universal.
Comes with handle.Note does not include shank.
-
$6.95Nukatap - Seal Kit
This pretty handy kit contails all the seals needed for both the standard Nukatap and the Flow Control Nukatap.
The majority of these seals would never normally need to be replaced, but in the event of accidental loss / extreme commercial use please replace washers with the addition of food-grade lubricant to ensure their longevity.
If you have not changed your seals before, it's a great idea to take a note of which seal goes where as you remove the old ones!
-
$1.95NukaTap Mini & NukaTap FC Gen2 - Self Closing Tap Spring
This Nukatap mini & Nukatap FC spring is designed to suit all Nukatap Mini taps and also the Nukatap Flow Control (FC) tap. This custom made 304 grade spring size is designed specifically to ensure your Nukatap stays closed when it should.
Simple let go of the tap handle and the tap will snap shut and prevent accidentally leaving the tap on and emptying the keg onto the floor.
-
$4.95DIY Tap Handle Inserts
DIY Tap Handle Inserts - Dual Threaded - 3/8″-16 threads, .625″ Length.
Want to make your own unique tap handles but the thread type is strange? These simplistic brass inserts are the answer.
All you'll need is a 12.7mm (1/2") hole drilled into your handle (Pine, Red Gum, Oak, Cherry, Maple, etc), then screw in with a large flat screw driver.
It is important not to push down too hard if you're going to using a screw driver, or wide drill bit. It will strip the thread. Let the piece cut into the wood. Ensure that it is straight.
Suits NukaTap and Intertap taps
Out of Stock
