Mashing

  1. Bazooka T Screen Bazooka T Screen
    $29.50

    Bazooka T Screen

    A stainless steel mesh Bazooka T Screen with 1/2" copper fitting. 

    Copper Fitting Diameter: 17 mm ID / 19 mm OD
    Material: Stainless Steel 304 mesh and copper fitting

  2. Domed Stainless Steel False Bottom (39cm) kit Domed Stainless Steel False Bottom (39cm) kit
    $60.00

    Domed Stainless Steel False Bottom (39cm) kit

    This is a domed false bottom made from stainless steel. It comes complete with stainless steel elbow and 3/8" barbed outlet. These false bottoms are often used for helping to construct a mash tun.
  3. Domed Stainless Steel False Bottom (30cm) kit Domed Stainless Steel False Bottom (30cm) kit
    $58.00

    Domed Stainless Steel False Bottom (30cm) kit

    This is a domed false bottom made from stainless steel. It comes complete with stainless steel elbow and 3/8" barbed outlet. These false bottoms are often used for helping to construct a mash tun.

  4. Manifold for Mash Recirculation Manifold for Mash Recirculation
    $80.00

    Manifold for Mash Recirculation

    Manifold for Mash Recirculation, intended for, but not limited to, the Ss InfuSsion Mash Tun.

    - 304 Stainless construction
    - Sits on top of grain bed during mash
    - Gentle distributed flow through 24 holes drilled into the top side of the manifold
    - 3/8" hose barb on manifold inlet
    - Compatible with the recirculation bullkhead fitting and 1/2" FPT to 3/8" knurled hose barb
    - Will fit in 38 / 76 gal Ss InfuSsion Mash Tuns, and 38, 57, 76, 114 litre brew kettles
    - approx. 32cm total diameter

    From: Ss Brewing Technologies, USA

  5. Ss InfuSsion Mash Tun Ss InfuSsion Mash Tun
    $645.00

    Ss InfuSsion Mash Tun

    The InfuSsion Mash Tun from Ss Brewing Technologies is targeted at brewers doing infusion mashing in insulated chilly bins and are looking for a better performing piece of equipment made of 304 Stainless Steel that is purposefully built for brewing.

    In side by side testing, the 10 gallon InfuSsion Mash Tun showed 3 degrees less of temperature decay over a 60 minute mash as compared to a similarly sized plastic chilly bin. The InfuSsion Mash Tun also has a concave recess under the false bottom which has a centre located drain that plumbs out to a 1/2" ball valve. By locating the drain port in the middle we are able to get better uniformity and efficiency through the grain bed versus a traditional plastic chilly bin setup.

    Features:

    • Dual wall (foam insulated) high grade 304 Stainless Steel
    • Centre drain and 5 degree sloped bottom
    • No dead space, conical bottom with drain
    • Foam insulated lid for heat retention
    • Electrically etched volume markings in gallons
    • Includes false bottom with silicone gasket
    • Includes thermowell
    • Includes precision LCD thermometer
    • Includes high quality 304 Stainless Steel 3 piece ball valve

    The 76 litre model also comes with a recirculation port.

    Available in these sizes:

    • 38 Litre (10 Gal)
    • 76 Litre (20 Gal) +$250

    Note: this mash tun cannot be used with a burner.

    Upgrade options include the MTSs Temperature Controller for the InfuSsion Mash Tun, designed to ensure a constant mashing temperature, and a sparge arm.

  6. RIMS Heat Stick Heat exchanger housing RIMS Heat Stick Heat exchanger housing
    $129.95

    RIMS Heat Stick Heat exchanger housing

    A stainless heat stick housing to help make a RIMS recirculating mash system.

    They have been made with TIG welded 50mm stainless pipe with 2 x ½” BSP female sockets at right angles in the top and bottom for the wort to flow in and out.

    On each end there is a tri-clamp end cap, one with a 32m hole pre-drilled so it is ready to mount one of our 2200watt elements. The other end cap has a 20mm hole so it is ready to mount either a thermowell or bulkhead. This makes it easy to then use our temperature controller and pump to build your own re-circulating RIMS system.

    Includes:

    • 1 x RIMS tube TIG welded from 304 stainless
    • 2 x Silicone beaded seals
    • 2 x Tri-clamp clamps
    • 2" - 1 x End plate with 32mm hole
    • 1 x End plate with 20.5mm hole

    Note: does not include bulkhead, temperature probe or element.

    Out of Stock
  7. MTSs Temp Controller for Infusion Mash Tun
    $149.95

    MTSs Temp Controller for Infusion Mash Tun

    The MTSs Temperature Controller is designed for use with Ss Brew Tech's Infusion Mash Tun.

    During extended Mash periods or in relatively cold ambient temperatures, the mash will naturally drop in temperature. With the MTSs you will be able to provide better controlled temperatures during the mash scarification process. Holding a consistent scarification temperature will insure you are making the beer and flavour profiles you planned to produce.

    The MTSs is a low wattage silicone heater pad, which is bonded to the underside of the 5 degree sloped bottom on your Mash Tun using a strong adhesive backing on the heater pad. The heater is controlled with a 12 volt digital temp controller. You simply set your target temperature and the heater will cycle on and off to maintain your set point.

    This system is not designed for heating water to strike temp and/or step mashing, though it can help with fine tuning your strike water temp those last few degrees and/or maintaining your strike water temp while you are preparing your grist or balancing your water chemistry.

    Features:

    • Keep your mash temperature stable
    • Holds mash temp to within 1 degree of set point
    • 12V adhesive heater pad
    • 6A 12V Power supply (bigger than FTSs)
    • Digital temp controller
    • Grommet / zip tie (for strain relief)
    Out of Stock