Robobrew / BrewZilla
-
$79.95BrewZilla 35L - Replacement Stainless Immersion wort Chiller
BrewZilla - Replacement Stainless Immersion Chiller. Can be used in any all grain set up - up to 25l batch size.
Coiled part of the chiller: 24cm high & 19cm diameter
Total height of the chiller: 41cm
Tubing: 12.7mm, 304 Stainless SteelOut of Stock -
$15.50BrewZilla 35L - Replacement Wire Malt Pipe Support (Halo Ring)
This is a replacement wire support for the BrewZilla 35L model. It can also be used on the Digiboil 35L model so you can use a malt pipe with the Digiboil 35L boiler.
Out of Stock -
$25.00BrewZilla 35L - Replacement Top Screen for Malt Pipe
This piece helps when using the over flow pipe to not get grain into the boiler.
-
$38.5035L BrewZilla Gen 3 - Bottom Screen for Malt Pipe with threaded socket
Replacement bottom screen for malt pipe. Can be used on Generation 2 models.
-
$14.20BrewZilla 35L Gen3 - Malt Pipe Handle (only)
Our unique design in the new Gen3 handle allows you to set up a rigging device without the attatchments slipping to either side of the handle.
*Malt Pipe Not included*
Out of Stock -
$29.95BrewZilla Double Pulley Set
This double stainless steel pulley set will make it easy to lift your malt pipe from your BrewZilla, Robobrew, Grainfather, Braumeister, Brewtools, or other single vessel brewery.If you are looking for the easy way to lift your malt pipe from your single vessel brewery then this is the easy way to do it. The setup includes all the parts you need. Simply screw the shackle into the roof or overhead beam and then secure the wall cleat and away you go. It will only take a couple moments to install. The double pulley is used so it's possible to lift the large malt pipe in the 65L BrewZilla unit.This stainless steel pulley set has been made from all 304 grade stainless steel, nylon and non-corrosive materials. -
$79.95Brewzilla Boiler Extender - Extension Kit
Brewzilla Boiler Extension - for 35L and 65L units. Also suits Digiboils as well.
Ever wanted to punch out a few more litres of wort with your BrewZilla? Maybe you wanted more strike water for a super sticky batch. Maybe you get boil overs a lot and would like a bit of extra protection. Now theres a solution! The all new BrewZilla boiler extension that allows 12L headroom on a 35L unit and 24L on a 65L.
Turn that a 35L BrewZilla into a 47L behemoth, or the 65L Brewzilla to 89L! -
$795.00BrewZilla Gen 4.1 - Single Vessel Brewery - 35 Litre
The BrewZilla Gen 4 is designed to be a compact single vessel all grain home brewing system that can be run off a single 220-240v socket. A complete turnkey system with a delay timing feature and step mash functionality. Built to make batches up to 30L, it is the ideal solution for those who want to take the first step in all-grain brewing while also wanting full control of their batch from start to finish.
Fast to setup, brew and clean up is easy The very simple design is easy and intuitive to use.
-
$1,095.00BrewZilla Gen 4 - Single Vessel Brewery - 65 Litre
The BrewZilla Gen 4 is designed to be a compact single vessel, double batch all grain home brewing system that can be run off a 15 amp socket.
A complete turnkey system with a delay timing feature and step mash functionality. Built to make batches up to 60L, it is the next stepping stone up from the 35L BrewZilla model, being the ideal double batch system for those who want full control of their brew from start to finish. -
$44.95BrewZilla Gen 4 Neoprene Jacket
BrewZilla Gen 4 Neoprene Jacket / Parka with Recirculation Arm Cover
New and improved BrewZilla Gen 4 Neoprene Jacket for more stable mash temperatures and heat retention. Now made with 8mm thick neoprene, improved recirculation pipe insulation on both the boiler and the recirculation camlock arm.
If you brew outside where it is cold or windy, the Neoprene Jacket/Parka is a must-buy! Don't lose that heat to the atmosphere!
Available for both 35L and 65L Brewzilla Gen 4 units.
