Chilling
-
Stainless Steel Immersion Wort Chiller – 7.5m length
Stainless Steel Immersion Wort Chiller – 7.5m length
Immersion chillers are the easiest to use and clean chillers for all grain brewers. Just drop it into your hot wort and turn on the water. Occasional stirring or recirculating with a pump will reduce cooling times considerably.Outer diameter of the stainless steel tube is 10mm. The total diameter of the coil is approximately 250mm.
-
Copper Immersion Wort Chiller – 7.5m length
Copper Immersion Wort Chiller – 7.5m length
Immersion chillers are the easiest to use and clean chillers for all grain brewers. Just drop it into your hot wort and turn on the water. Occasional stirring or recirculating with a pump will reduce cooling times considerably.Outer diameter of the copper tube is 10mm. The total diameter of the coil is approximately 250mm.
-
Plate Chiller MKIII Chillout – 30 Plates
The Chillout MKIII is the fastest way to chill your wort to yeast pitching temperature to get your fermentation off to a quick healthy start. The Chillout is made from stainless steel and brazed together with pure copper. It also has ripples up and down each plate. This creates more surface area and improves heat transfer. Dimensions: 315mm x 73mm x 73mm -
Wort Heat Exchanger - Counterflow Chiller
These copper counter flow chillers are a fast way to chill your wort. They have similar efficiency to the plate chillers, however can be easier to clean as they do not have all the small crevasses to trap hop material and other solids.
The copper is a very good conductor of heat. These units are 23cm in diameter and about 18cm high. The input and output are approximately 10mm outside diameter. These can be used with gravity but it is recommended to use with a pump.Out of Stock -
Robobrew - Replacement Stainless Immersion wort Chiller
Robobrew - Replacement Stainless Immersion Chiller. Can be used in any all grain set up - up to 25l batch size.
Coiled part of the chiller: 24cm high & 19cm diameter
Total height of the chiller: 41cm
Tubing: 12.7mm, 304 Stainless Steel -
BrewZilla - Replacement Stainless Immersion Chiller - 65 Litr
BrewZilla / Robobrew - Replacement Stainless Immersion Chiller for the 65 Litre model.Out of Stock -
G-20 IceMaster G20 Glycol Chiller - With Integrated Pumps and Digital Control
IceMaster G20 - Glycol Chiller - Digital Fermentation Control - (with 2 integrated pumps for dual temp).
The Icemaster G20 is an efficient glycol chiller that has fantastic cooling performance. It's compact, quiet and ideal for a domestic environment. It is powerful enough to chill well-insulated fermenters up to 300L in size or multiple smaller fermenters. It has about 600-watt cooling power making it suitable for crash chilling even in hot ambient temperatures in your garage or brewery.For more specs, check out the Long Description
-
Coolossus - Stainless Counter Flow Chiller
Coolossus - Passivated Stainless Steel Counterflow Chiller with 1/2 inch BSP male thread connectors.
Chill your wort down like a pro! This 6.5m fully 304 passivated stainless steel chiller can withstand high hop additions without clogging. The Coolossus also has high chemical resistance unlike plate chillers and other copper immersion chillers.
Specifications:
Coolant Line: ID: 21mm x OD: 22mm x Length 6m;
Wort (Beer) Line: ID:11.9mm x OD12.7mm x Length 6.5m
Height: 180mm
Diameter: 280mm
Connectors: 1/2” BSPT (Ideal for hose connectors such as Camlocks or Quick Disconnects)
Composition: 304 Stainless SteelFrom: Kegland
Out of Stock -
New$269.00
Grainfather Glycol Chiller Adapter
The Glycol Chiller Adapter (GCA) is designed to expand on the capabilities of the Grainfather Glycol Chiller, by allowing almost any fermenter on the market to be connected, and temperature controlled - including most plastic bucket fermenters!
The Glycol Chiller Adapter works in a similar way to the Conical Fermenter Pro but instead of the built-in cooling sleeve and heating element, it uses a stainless steel cooling coil and a heating pad to control the temperature of almost any fermenter.
The cooling coil is connected to the Glycol Chiller and immersed in the fermenter. The heating pad is attached to the side of the fermenter using hook and loop tape. A temperature probe is also attached to the fermenter and the GCA will then regulate the cooling, or heating, as required.
The GCA connects to the Grainfather App so you can control your fermentation temperature on the go.
Out of Stock