Fermenters
-
$25.00Grainfather Conical Pressure Transfer - Upgrade connection KIT
This upgrade kit will complete the Grainfather Conical Fermenter Pressure Transfer.
Connect your Grainfather Conical Fermenter Pressure Transfer to your CO2 line and corny keg easily with this upgrade kit.
*Note does not include the Grainfather Conical Fermenter Pressure Transfer in photo.
-
$15.20FermZilla - 3" Tri-Conical - 600ml Collection Container
This collection container fits all the FermZilla Tri-Conical fermenters that have a 3 inch x 3 inch butterfly valve. No more threads or removal tools to get this off, simply depressurise and remove the tri-clamp fitting. We'd recommend placing a towel or upside down frisby to catch some drips.
-
$12.9560cm Thermowell - 1/4inch Duotight Bulkhead Included
This thermowell fits into any 8mm Hole and can literally be installed into almost any fermenter lid.
-
$14.95FTSs Controller Mounting Bracket
A mounting bracket for Ss Brewtech fermenters. Mounts to the vessel's thermowell port for all Chronical fermenters and standard Brite Tanks, or to the tri-clamp bracket for Unitanks and Brewmaster Brite Tanks. - Custom tooled shelf for FTSs controllers - Thermowell Bracket is matte black - Tri-Clamp Bracket is 304 Stainless From: Ss Brewtech -
$15.00FermZilla - All Rounder 30L/60L Base Support Webbing / Strap / Bridle / Carry Tie Down
This handy little strap will make cleaning and transport your FermZilla All Rounder 30L or 60L an absolute breeze. Simply attach through both sections of the base in the orientation you wish. Slide up and out of the little buckle pieces making sure that the buckle is facing towards you, then strap in and strap down!
The Strap is long enough for the 60L FZ-AR and 30L. We recommend rolling up the excess strap and paper clipping or cutting to suit the 30L.Out of Stock -
$89.95Ss CIP Spray Ball Tri-Clamp Attachment 3"
CIP Spray Ball Tri-Clamp Attachment
- Made from 304 Stainless Steel
- 3" tri-clamp cap with 1/2" MPT
- 2 bar / 29 psi recommended
- Use on any 3" tri-clamp fitting -
$12.95Push In Pressure Gauge - 8mm
This push in gauge is ideal to read pressures during pressurised fermentation. The triple scale gauge gives readings in Bar, PSI and kPA so irrespective of what units you prefer this gauge will display what you need.
The barb on this gauge will enable you to put this directly onto hosing or alternatively you can connect it to any of the push in fittings such as the Duotight push in fittings in the 8mm size.
Specifications:
- 0-40psi / 0-250kPa / 0-2.5 Bar (kg/cm^2)
- Rubber Coated
- 8mm Push in Barb
From: Kegland -
$64.955L Propylene Glycol - Kegland
Food grade Propylene Glycol (99%) from Kegland in a handy 5 litre container.
-
$1.00Thermowell and FTSs Chiller Coil - Ss Replacement O-Ring
Ss Replacement O-Ring for SS Brewtech Thermowells and FTSs Chiller Coils.
From: Ss Brewing Technologies, USA
A cheap, small but critical part of your brewkit, don't let a damaged o-ring spoil your brewday. -
$9.50Sterilock Air Lock (with one odour capsule)
The Sterilock contains a patented nanoseal that removes fermentation odours and allows C02 gases to safely vent while preventing any contaminants (including bacteria) to enter the fermentation vessel.
