Equipment

  1. 60cm Thermowell - 1/4inch Duotight Bulkhead Included 60cm Thermowell - 1/4inch Duotight Bulkhead Included
    $12.95

    60cm Thermowell - 1/4inch Duotight Bulkhead Included

    This thermowell fits into any 8mm Hole and can literally be installed into almost any fermenter lid.

    Out of Stock
  2. Ss CIP Spray Ball Tri-Clamp Attachment 3"
    $80.00

    Ss CIP Spray Ball Tri-Clamp Attachment 3"

    CIP Spray Ball Tri-Clamp Attachment

    - Made from 304 Stainless Steel
    - 3" tri-clamp cap with 1/2" MPT
    - 2 bar / 29 psi recommended 
    - Use on any 3" tri-clamp fitting

  3. Thermowell and FTSs Chiller Coil - Ss Replacement O-Ring
    $1.00

    Thermowell and FTSs Chiller Coil - Ss Replacement O-Ring

    Ss Replacement O-Ring for SS Brewtech Thermowells and FTSs Chiller Coils.

    From: Ss Brewing Technologies, USA

    A cheap, small but critical part of your brewkit, don't let a damaged o-ring spoil your brewday.
  4. 5L Propylene Glycol - Kegland 5L Propylene Glycol - Kegland
    $64.95

    5L Propylene Glycol - Kegland

    Food grade Propylene Glycol (99%) from Kegland in a handy 5 litre container.


  5. Super Automatica Tirage Bell - 29/31mm (large) Super Automatica Tirage Bell - 29/31mm (large)
    $21.70

    Super Automatica Tirage Bell - 29/31mm (large)

    For use on the Red handle "Super Automatica Capper" with Tirage Bells. The standard bell supplied with the Super Automatica Capper is 26mm. This larger 31mm bell is compatible with slightly larger caps and bottle tops.

    IMPORTANT: This bell is NOT compatible with the "Green Standard Bench Capper"  OR "Lever Bench Capper" - due to different thread size.

  6. Wing Nut for Beer Shank
    $4.00

    Wing Nut for Beer Shank

    Chrome plated brass wing nut, often used for attaching a tail piece to a shank. A handy alternative to the standard 5/8" hex nut if you have an application where you wish to be able to disassemble the shank tail piece without using a wrench.
  7. Stainless Steel Flange For Shank
    $5.00

    Stainless Steel Flange For Shank

    Stainless steel flange for standard beer shanks, as an alternative to the standard black plastic option.
    Out of Stock
  8. Silicone Washer Seal - 5/8 for Keg Coupler and Tap Shank
    $0.50

    Silicone Washer Seal - 5/8 for Keg Coupler and Tap Shank

    A 5/8" silicone washer seal for Keg Coupler or Tap Shank.

    Note: may come in black or white/clear.

    Silicone washer seals are easier to get a proper seal but are also easier to damage. If you are looking for a more robust solution consider using a 5/8" neoprene washer instead.
    Out of Stock
  9. Locking Wall Flange for Shank Assembly
    $8.00

    Locking Wall Flange for Shank Assembly

    The Locking Wall Flange allows you to hold the shank securely in place by fitting three screws that mount the flange to the inside of the door or wall.
  10. Faucet Coupling Nut
    $5.00

    Faucet Coupling Nut

    Chrome plated brass faucet coupling nut to attach a beer tap to a shank. Works with most standard beer fittings.
    With this faucet replacement nut you can renew a worn-out part on your well-used draft faucet.
    Out of Stock