Connections and Valves

  1. Grainfather S40 Tap & Nut
    $51.50

    Grainfather S40 Tap & Nut

    Replacement Tap & Nut for the S40
  2. Grainfather G70 1/2" Tee
    $14.10

    Grainfather G70 1/2" Tee

    Replacement 1/2" Tee for the G70
  3. Duotight - 9.5mm One Way Check Valve (Gas)
    $6.95

    Duotight - 9.5mm One Way Check Valve (Gas)

    This elbow piece is suitable for the EVABarrier Beer & Gas line in 9.5mm (3/8") OD line to 6.3mm (1/4") ID.

  4. FermZilla Tri-Conical - 2" x 2" Tri-Clamp Butterfly Valve FermZilla Tri-Conical - 2
    $49.95

    FermZilla Tri-Conical - 2" x 2" Tri-Clamp Butterfly Valve

    Compatible with any 2 Inch tri-clamp fitting. Primarily designed for the:
    FermZilla 2" Tri-Clamp Lid
    - in conjunction with the 2" Tri-Clamp Hop Bong

    If you are looking to put your FermZilla Tri-Conical / All Rounder in a Fermentation Chamber / Fridge, you will want to allow 420mm measured from the base of the ring collar to a comfortable level to pull the pressure relief valve to purge oxygen from the hop bong.

  5. Keg Lube
    $9.95

    Keg Lube

    Clear lubrication gel for keg parts such as o-rings, couplers, party pumps. Use with plastic and rubber components to avoid cracks and extend their life. Just a little of this goes a long way.
    Out of Stock
  6. Tri-Clamp Cap - 6" to 3" Reducer Tri-Clamp Cap - 6
    $59.95

    Tri-Clamp Cap - 6" to 3" Reducer

    Tri-Clamp Cap - 6" to 3" Reducer. Great for 10 Gal Brite Tanks or 52/76L Unitanks.

    Note: gaskets not included, but you can find them here.

  7. Tri-Clamp Cap - 3" to 1.5" Reducer Tri-Clamp Cap - 3
    $39.95

    Tri-Clamp Cap - 3" to 1.5" Reducer

    Tri-Clamp Cap - 3" to 1.5" Reducer. Great for allow you to use existing 1.5" tri-clamp fittings on a 3" TC fermenter.

    Note: 3" gasket not included.

  8. Hole Punch - 22mm and 33mm Hole Punch - 22mm and 33mm
    $12.95

    Hole Punch - 22mm and 33mm

    These hole punches are great for making really clean holes that are free of burrs. The holes made with this type of punch are significantly better than a hole made with a carbide drill bit or many other hole saws. These produce clean holes and can be used in mild sheet steel up to 3mm thick or stainless steel up to about 1.5mm thick. If you are looking for a really easy way to make really clean holes this is the best product for the job.

    Available for a 22mm or 32mm hole.

    Out of Stock
  9. 1/2" Inch BSP 316 stainless hex Back Nut
    $6.10

    1/2" Inch BSP 316 stainless hex Back Nut

    Used in conjunction with a hex nipple, washer and ball valve assembly.
  10. 22MM Stainless steel Flat Washer
    $2.50

    22MM Stainless steel Flat Washer

    Good for hex nipples, and putting pressure on seals.