Connectors
-
$4.95Duotight Push In For MFL Connector - 8mm
Easily connect your beer or gas line to your MFL fitting.
Note: MFL keg connector and tubing sold separately.Brand: Duotight
-
$5.00Duotight - 8mm Ball Valve
Duotight - 8mm shut off ball valve. This is an equal ball valve to take 8mm OD tubing in both sides.
No clamps necessary!
From: Kegland -
$5.00Duotight - 8mm Push-Fit Check Valve
Duotight 8mm (5/16) one way check valve/non-return valve.
From: Kegland -
$9.00Tail Piece with 1/4" MFL Connector
Tail piece for your dispensing system that provides a 1/4" MFL connector instead of a barb.
From: Krome Dispense
Material: 304 grade stainless steel
Looking for the full setup? Designed to be used with a 5/8" hex nut and a 5/8" neoprene washer. These items sold separately. -
$5.00Duotight Push Fit Tee connector 8mm
This push-fit T-Connector will split the gas (or beer) line on your kegging system in two, allowing you to gas two kegs at the same time. Simple to use and requires no tools. -
$5.00Duotight Push-Fit Elbow 8mm
This Push-Fit Elbow - 8mm x 8mm - will allow you to join beer or gas line sections on your kegging system. Simple to use and requires no tools. -
$5.00Elbow Pipe Joiner 1/4" x 1/4"
Elbow Pipe Joiner for your keg dispensing system. These simple draft beer parts can extend or repair your beer and gas line. -
$5.00Elbow Pipe Joiner 3/16" x 3/16"
Elbow Pipe Joiner for your keg dispensing system. These simple draft beer parts can extend or repair your beer and gas line. Made of stainless steel, they’re designed to maintain the inside diameter of your hose. -
$15.00Elbow Bend - Low Profile - for coupler
This low profile elbow bend sits just 17mm above the top of the keg coupler. This makes it perfect for tight spaces or inside a Kegerator.
Note: You will need a washer/seal if you don't not have one (not included). -
$5.00 -
$5.00Barbed Swivel Nut - 1/4"
A Barbed Swivel Nut, often used for MFL fittings.
Bore size 6.35mm (1/4")Out of Stock -
$7.95Push-fit joiner - 10mm
This Push-Fit Joiner will allow you to join beer or gas line sections on your kegging system.
Note that this is 10mm diameter in and out.
They are extremely easy to use and allow you to simply push your beer and gas line straight into these fittings. No need to purchase clamps or tools.
To remove the fitting, simply push in the collet and the hose can be removed.
Fits 10mm outer diameter tube.
Note: colour may vary.
Out of Stock -
$6.95Stainless barbed tee piece - 1/4"
A barbed stainless steel T (tee) piece for splitting a keg line.
Bore size:
6.35mm (1/4") -
$10.00 -
$9.95Keg Connector - Duotight - Gas - 8mm
Duotight 8mm x Ball Lock Disconnect (Grey + Red/Gas)
This all new ball lock disconnect sets a new bar! The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably - no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitising an absolute breeze!
Made from highly chemical resistant materials with stainless springs and ball bearings - no cheap ABS plastics here - this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitisers and caustics.
