Other Homecrafts
-
$3.00EvaBarrier 4mm ID - 8mm OD hose / tube
This high quality beer line will keep your previous beverage in it's best possible conditoin in the process.
When using this 4mm ID size you will get adequate flow resistance with 1.5meters to 2.1meters of beer line between your keg and tap suitable for most kegerator setups.
Pressure Rating (with 1.5safety factor)
30C - 1.4 MPa (200psi)
50C - 0.7MPa (100psi) -
$3.50EvaBarrier 6.3mm ID - 9.5mm OD hose / tube
This high quality beer line will keep your previous beverage in it's best possible conditoin in the process.
Pressure Rating (with 1.5safety factor)
30C - 1.4 MPa (200psi)
50C - 0.7MPa (100psi) -
$4.95Push fit 1/4" to 3/8" tube to hose adaptor
A 1/4" x 3/8" tube to hose adaptor with a 1/4" hose barb and a 3/8" push-fit connection. -
$20.00Liquid Ball Lock Post with 5/8 Thread for keg coupler
Liquid Ball Lock Post with 5/8" Thread. These are a very popular accessory that allows you to convert a commercial keg coupler with 5/8" thread to a standard corny disconnect liquid post. This is the simplest way to allow you to serve beer from commercial kegs in a standard homebrew kegerator or keezer without modifying your beer and gas lines.
-
$14.95Diffusion Stone - 0.5 Micron (barbed)
A carbonation or aeration diffusion stone. This can be used as a way to aerate your wort prior to fermentation, or to speed up carbonation of the finished beer.
The barb fits 1/4" (6.35mm) ID tubing.
-
$19.00Gas Ball Lock Post with 5/8" Thread for keg coupler
Gas Ball Lock Post with 5/8" Thread. These are a very popular accessory that allows you to convert a commercial keg coupler with 5/8" thread to a standard corny disconnect gas post. This is the simplest way to allow you to serve beer from commercial kegs in a standard homebrew kegerator or keezer without modifying your beer and gas lines.
-
$54.95Kegerator Cover - Water Resistant (for Series 4 and X Kegerators)
The Kegarator Cover is an ideal solution for storing your Kegerator outside or exposed to water/dust or dirt. Keep your Kegerator in the best condition you can.
Suitable for all Series 4 and Series X tap configurations.
-
$19.95Hop Tube - Stainless Steel with Chain
This Hop Tube is made from 304 stainless steel and is ideal for addling larger amounts of hop pellets, flowers or spices to your RoboBrew / BrewZilla without blocking the pump. It can also be used in your Brewhouse Kettle/Boiler, 19L corny keg, and the FermZilla. It cannot fit in a standard 50L Keg as the opening is not wide enough. The fine mesh will prevent large particles from blocking the dip tube, pumps or chillers. It will hold approximately 150g of hop pellets, allowing for some space to permit full extraction of the hop oils. Ideal for dry hopping in the keg and can also be used for fruits, wood chips, spices and more. Includes a small ring so it can be hung from the keg lid or side of the vessel.
Diameter: approx. 66mm Heigh: approx. 300 mm.
-
$18.95Drip Tray - Plastic 30cm
A plastic drip tray for your beer taps with removable grill.
Material: Food Grade Polycarbonate
Colour: Black
Dimensions: approx. 30cm x 16cm
From: Krome Dispense -
$20.00Gas Ball Lock Post with 1/4 Inch Bulkhead Assembly
These ball lock posts include a 1/4 inch BSP thread so you can attach it to a wide range of other fittings.
The posts include a 20mm long thread, an o-ring, poppet, locking nut and short dip tube. This would enable you to make a keg out of any pressure vessel if you wanted to. The assembly can also be fitted to regulators, gas manifolds and various other items.
Both Gas and Liquid posts available.
From: Kegland
