Connectors
-
Duotight - 9.5mm (3/8) Female x 5/8 Female Thread (suits Keg Couplers and Tap Shanks)
This straight joiner is suitable for our EVABarrier Beer & Gas hosing in 6mm x 9.5mm line. This allows a direct duotight push fitting to attach directly to a keg coupler.
No clamps necessary!
-
Duotight 8mm (5/16) Female x 1/4 Inch BSP Male Thread (With Seated O-Ring)
This handy small duotight to male 1/4 BSP threaded piece. Particularly useful for many standard gas fittings. The 1/4 inch thread fits into the regulator body, manifolds and many other fittings that often use 1/4inch thread.
Brand: Duotight
Material: Plastic
-
Mini Gauge 0-15psi (0-1.5bar) - For Inline Duotight Regulator Or Blowtie
Mini Gauge 0-15psi (0-1.5bar) - for inline Duotight regulator or Blowtie.
This gauge is designed to fit into either our inline regulator or our Blowtie unit. These can be used for water or gas.
-
Duotight - 9.5mm (3/8) x 1/4" Male Thread
This straight joiner is suitable for EVABarrier Beer & Gas hosing in 6mm x 9.5mm line.
No clamps necessary!
-
Duotight - 8mm (5/16”) Female x 3/8" Male Thread (with O ring)
This piece is suitable for EVABarrier Beer & Gas hosing in 4mm ID & 5mm ID line or most lines with 8mm outer diameter.
No clamps necessary!
-
Duotight - Seal Kit for Flow Control Keg Connector
Seal Kit - duotight 8mm x Flow Control Ball Lock Disconnect
Please refer to the product photos for an exploded diagram of where the replacement seals and poppet placement. -
Keg Connector - Duotight Flow Control - 8mm Liquid
Duotight 8mm x Flow Control Ball Lock Disconnect (Black-Yellow/Liquid).
This all new ball lock disconnect sets a new bar! The integrated duotight design means you can connect your beer line directly, easily and reliably - no need for additional fittings or clamps. It is a robust and super compact compared to the previous Stainless Steel Flow Control Ball Lock that has been discontinued due to the difficulty in repeated tooling and overall cost of raw materials.
Out of Stock -
Duotight - 6.35mm (1/4) Screwlock x 8mm (5/16) - Reducer Elbow
These high quality acetal fittings are made with EPDM o-rings that are reliable, will not perish like cheaper rubber. The acetal plastic is also chemical and UV resistant so it will last for a long time even in testing conditions.
-
8mm OD BLT - Beer Line Tidy - Beer and Gas Line Organiser
This beer line tidy is a handle little part that will help you organise your beer and gas line inside your fridge, keezer, kegerator or cellar. This keeps your beer and gas plumbing neat and tidy so your draft system looks as good as it works. Designed to suit both 8mm outer diameter hosing like 4mm x 8mm EVABarrier and 5mm x 8mm EVABarrier hosing. It can also fit smaller 3mm x 6.35mm EVABarrier hosing but may slip out more easily than the standard 8mm outer diameter hosing.
Simply remove the was paper and use the strong 3M adhesive to attach this beer/gas line organiser to whatever device you like.
-
Duotight - 8mm (5/16") Female x 8mm (5/16") Female Bulkhead with 20mm Locknut
These high quality acetal fittings are made with EPDM o-rings that are reliable, will not perish like cheaper rubber. The acetal plastic is also chemical and UV resistant so it will last for a long time even in testing conditions.
This product is ideally suited to the 8mm (3/8") EVABarrier tubing.