Equipment
-
$6.95Stout Tap Repair Kit
A repair kit for the Krome stout tap.
Easily repair faucet leaks simply by replacing the gaskets used within. Refer to the secondary image to get a clear understanding of what goes where. It doesn’t need many tools for this job.
-
$59.95Kegmenter Lid with Ball Lock Posts, Dip Tube and PRV
This stainless 4inch tri-clover ball lock lid will enable you to turn your kegmenter into a uni tank, pressurisable fermenter or so it can be used as a keg.
This lid comes with a red pressure relief valve (that opens at 2.5bar - compatible thread to Cornelius type PRVs). The lid has accurately machined gas and liquid posts.
This lid is ideally suited to also fermenting under pressure so you can use a spunding valve/adjustable pressure relief valve so you can naturally carbonate during primary fermentation.
Out of Stock -
$89.95Ss CIP Spray Ball Tri-Clamp Attachment 3"
CIP Spray Ball Tri-Clamp Attachment
- Made from 304 Stainless Steel
- 3" tri-clamp cap with 1/2" MPT
- 2 bar / 29 psi recommended
- Use on any 3" tri-clamp fitting -
$8.00Locking Wall Flange for Shank Assembly
The Locking Wall Flange allows you to hold the shank securely in place by fitting three screws that mount the flange to the inside of the door or wall. -
$0.50Silicone Washer Seal - 5/8 for Keg Coupler and Tap Shank
A 5/8" silicone washer seal for Keg Coupler or Tap Shank.
Note: may come in black or white/clear.
Silicone washer seals are easier to get a proper seal but are also easier to damage. If you are looking for a more robust solution consider using a 5/8" neoprene washer instead.Out of Stock -
$4.00Wing Nut for Beer Shank
Chrome plated brass wing nut, often used for attaching a tail piece to a shank. A handy alternative to the standard 5/8" hex nut if you have an application where you wish to be able to disassemble the shank tail piece without using a wrench. -
$23.50Super Automatica Tirage Bell - 29/31mm (large)
For use on the Red handle "Super Automatica Capper" with Tirage Bells. The standard bell supplied with the Super Automatica Capper is 26mm. This larger 31mm bell is compatible with slightly larger caps and bottle tops.
IMPORTANT: This bell is NOT compatible with the "Green Standard Bench Capper" OR "Lever Bench Capper" - due to different thread size.
-
$12.95Push In Pressure Gauge - 8mm
This push in gauge is ideal to read pressures during pressurised fermentation. The triple scale gauge gives readings in Bar, PSI and kPA so irrespective of what units you prefer this gauge will display what you need.
The barb on this gauge will enable you to put this directly onto hosing or alternatively you can connect it to any of the push in fittings such as the Duotight push in fittings in the 8mm size.
Specifications:
- 0-40psi / 0-250kPa / 0-2.5 Bar (kg/cm^2)
- Rubber Coated
- 8mm Push in Barb
From: Kegland -
$64.955L Propylene Glycol - Kegland
Food grade Propylene Glycol (99%) from Kegland in a handy 5 litre container.
-
$1.00Thermowell and FTSs Chiller Coil - Ss Replacement O-Ring
Ss Replacement O-Ring for SS Brewtech Thermowells and FTSs Chiller Coils.
From: Ss Brewing Technologies, USA
A cheap, small but critical part of your brewkit, don't let a damaged o-ring spoil your brewday.
