All-in-one Systems
-
BrewZilla 35L - Replacement Stainless Immersion wort Chiller
BrewZilla - Replacement Stainless Immersion Chiller. Can be used in any all grain set up - up to 25l batch size.
Coiled part of the chiller: 24cm high & 19cm diameter
Total height of the chiller: 41cm
Tubing: 12.7mm, 304 Stainless SteelOut of Stock -
Brewzilla Boiler Extender - Extension Kit
Brewzilla Boiler Extension - for 35L and 65L units. Also suits Digiboils as well.
Ever wanted to punch out a few more litres of wort with your BrewZilla? Maybe you wanted more strike water for a super sticky batch. Maybe you get boil overs a lot and would like a bit of extra protection. Now theres a solution! The all new BrewZilla boiler extension that allows 12L headroom on a 35L unit and 24L on a 65L.
Turn that a 35L BrewZilla into a 47L behemoth, or the 65L Brewzilla to 89L! -
BrewZilla Gen 4.1 - Single Vessel Brewery - 35 Litre
5L BrewZilla Generation 4.1
Wifi / RAPT IntegrationThe BrewZilla Gen 4 is designed to be a compact single vessel all grain home brewing system that can be run off a single 220-240v socket. A complete turnkey system with a delay timing feature and step mash functionality. Built to make batches up to 30L, it is the ideal solution for those who want to take the first step in all-grain brewing while also wanting full control of their batch from start to finish.
-
BrewZilla Gen 4.1 - Single Vessel Brewery - 65 Litre
65L BrewZilla Generation 4.1
Wifi / RAPT Integration
With 25w Pump 2000w/1000/500w - 220-240V ACThe BrewZilla Gen 4 is designed to be a compact single vessel, double batch all grain home brewing system that can be run off a 15 amp socket. It is a complete turnkey system with a delay timing feature and step mash functionality. Built to make batches up to 60L, it is the next stepping stone up from the 35L BrewZilla model, being the ideal double batch system for those who want full control of their brew from start to finish.
-
BrewZilla Gen 4 Neoprene Jacket
BrewZilla Gen 4 Neoprene Jacket / Parka with Recirculation Arm Cover
New and improved BrewZilla Gen 4 Neoprene Jacket for more stable mash temperatures and heat retention. Now made with 8mm thick neoprene, improved recirculation pipe insulation on both the boiler and the recirculation camlock arm.
If you brew outside where it is cold or windy, the Neoprene Jacket/Parka is a must-buy! Don't lose that heat to the atmosphere!
Available for both 35L and 65L Brewzilla Gen 4 units.
-
BrewZilla + DigiBoil S.S Adjustable Lid Clamps - Short (4pcs/set)
Get the exact tension you need with your BrewZilla, DigiBoil or even GrainFather with Kegland's Stainless Steel Adjustable Clamp Set. Adjust to your specification.
This set of 4 adjustable stainless steel clamp set suits the 35L and 65L BrewZilla Gen 3 all the way to Gen 4 as well as all 35L and 65L DigiBoils. It also suits the 12L and 24L Boiler Extensions.
-
BrewZilla Gen 4 - Heat Exchanger Dish (HED)
What does it do?
Due to the concave bottom and central draining hole, the wort being recirculated through the pump will pass through the malt pipe and then down through the boiler false bottom. The wort would normally then follow the path of least resistance, making a b-line for that drainage hole.What this Heat Exchanger Dish does is force that recirculating wort up to the edge of the BrewZilla base and pass over the elements for a longer period, this then aids in faster heating exchange with the wort, which can help you on a brew day reach those temperatures much quicker.
This is an upgradeable accessory to the 35L BrewZilla Generation 4 only. It is not compatible with any previous generations of BrewZilla, RoboBrew or DigiBoils.
-
BrewZilla Double Pulley Set
This double stainless steel pulley set will make it easy to lift your malt pipe from your BrewZilla, Robobrew, Grainfather, Braumeister, Brewtools, or other single vessel brewery.If you are looking for the easy way to lift your malt pipe from your single vessel brewery then this is the easy way to do it. The setup includes all the parts you need. Simply screw the shackle into the roof or overhead beam and then secure the wall cleat and away you go. It will only take a couple moments to install. The double pulley is used so it's possible to lift the large malt pipe in the 65L BrewZilla unit.This stainless steel pulley set has been made from all 304 grade stainless steel, nylon and non-corrosive materials.Out of Stock -
35L BrewZilla Gen 3 - Bottom Screen for Malt Pipe with threaded socket
Replacement bottom screen for malt pipe. Can be used on Generation 2 models.
-
BrewZilla 35L - Replacement Top Screen for Malt Pipe
This piece helps when using the over flow pipe to not get grain into the boiler.
-
BrewZilla 35L - Replacement Malt Pipe
This is a replacement malt pipe for the BrewZilla 35L model. It can also be used on the Digiboil 35L model so you can use a malt pipe with the Digiboil 35L boiler.
270mm Diameter
385mm HighOut of Stock -
35L + 65L BrewZilla Gen 3.1.1 - LCD Display Screen (control panel)
This board will allow you to upgrade from Brewzilla 3.1 to 3.1.1 to take advantage of some new features. To see the difference or to do the upgrade you can see this instruction sheet that explains this upgrade in more detail.
If you currently own a 3.1 unit all you will need is the LCD Control Panel. You will not need a new PCB Board (Power Board)From: Kegland
-
Brewzilla Replacement Glass Lid 35L with hole
A replacement lid (no handle knobs) for your Robobrew / Brewzilla, with centre hole. Black knobs for the lid are sold separately.
-
Stainless Flexi Arm
Stainless Flexi Arm 40cm with 1/2inch BSP Hex Nut Female.
Perfect for sparging arms, recirculation piping for the 35L and 65L BrewZilla. Please note you will need a Male Camlock to Male 1/2" BSP Thread (F Type) in order to attach to your BrewZilla recirculation arm (sold separately).
From: Kegland
-
BrewZilla 65L / DigiBoil 65L - Replacement Glass Lid (420mm) with Hole (no handle knobs)
Put up your hand if you've smashed or lost one of these BrewZilla glass lids, the answer will shock you!
We all do it, but if you're wanting to keep everything the same and want to be able to re-sell your BrewZilla, we'd recommend purchasing it for a full set.Out of Stock -
BrewZilla 35L False Bottom (Pump Filter)
A replacement BrewZilla 35L False Bottom.
This attachment stops particulates from blocking your pump and getting into your beer.
Designed to be used on all BrewZilla 35L units.
Out of Stock -
New$89.95
Heavy Duty False Bottom for DigiBoil and BrewZilla
Designed exclusively for the 3 Vessel homebrewing market that wants to take full use of a DigiBoil to be used as a Mash Tun/Lauter Vessel. It can also be used on the BrewZilla Gen4 and 3.1.1 units if you wish.